+高级检索
激光熔覆层宽度对汽轮机转子表面综合跳动特性的影响
DOI:
作者:
作者单位:

中原工学院机电学院,中原工学院机电学院,中原工学院机电学院,中原工学院机电学院,浙江工业大学

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金项目,河南省高校重点科研项目


Effects of Laser Cladding Layers Width on Total Indicated Runout Characteristics of Steam Turbine Rotor Surface
Author:
Affiliation:

School of Mechanical Electronic Engineering,Zhongyuan University of Technology,School of Mechanical Electronic Engineering,Zhongyuan University of Technology,School of Mechanical Electronic Engineering,Zhongyuan University of Technology,School of Mechanical Electronic Engineering,Zhongyuan University of Technology,Research Center of Laser Processing Technology and Engineering,Zhejiang University of Technology

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    为解决大型汽轮机转子轴轴颈磨损的修复问题,基于同轴送粉半导体激光熔覆再制造系统,采用激光熔覆再制造方法,以汽轮机转子轴材料为基体,利用激光熔覆再制造专用粉末作为实验材料,针对不同激光熔覆层宽度对汽轮机转子综合跳动的影响进行实验研究与机理模拟验证。结果表明,综合跳动特性与探头直径和激光熔覆层宽度相关,激光熔覆层宽度决定了汽轮机转子表面磁力线、电涡流密度与磁通量密度分布。当激光再制造层宽度小于8mm时,由于磁力线与表面电涡流密度受基体的干扰,磁通量密度在激光熔覆层的边缘出现突变,实际综合跳动的测量值为基体与激光熔覆层综合作用的结果,造成测量结果偏大。根据数值模拟计算被测金属体表面磁通量密度分布结果,激光熔覆层宽度的临界值为9.82mm。

    Abstract:

    In order to solve the wear repair problem of large steam turbine rotor shaft journal, the material of steam turbine rotor shaft as substrate and the self-made special laser cladding remanufacturing powder as experimental material, the experiments were carried out by laser cladding remanufacturing method based on laser cladding remanufacturing system with coaxial powder feeder. Focusing on effect of different width of laser cladding layers on total indicated runout (TIR) of steam turbine rotor, the experiment research and mechanism simulation verification were performed, and the influence mechanism of different factors were analyzed. The results show that the data results of total indicated runout are closely related to probe diameter and laser cladding layer width. The width of cladding layer determines the turbine rotor surface magnetic, eddy current density and magnetic flux density distribution. Due to the interference of matrix magnetic field and eddy current density of surface, the magnetic flux density suddenly changes in the laser cladding layer edge when the laser cladding layer width is less than 8mm.The measurement results are too large caused by the comprehensive effect of substrate and laser cladding layer. According to the numerical simulation of magnetic flux density distribution of measured metal body surface, the critical value of laser cladding width is 9.82mm.

    参考文献
    相似文献
    引证文献
引用本文

郭士锐,尚会超,崔陆军,郭小锋,姚建华.激光熔覆层宽度对汽轮机转子表面综合跳动特性的影响[J].稀有金属材料与工程,2017,46(3):612~616.[Shirui Guo, Huichao Shang, Lujun Cui, Xiaofeng Guo, Jianhua Yao. Effects of Laser Cladding Layers Width on Total Indicated Runout Characteristics of Steam Turbine Rotor Surface[J]. Rare Metal Materials and Engineering,2017,46(3):612~616.]
DOI:[doi]

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:2015-09-12
  • 最后修改日期:2015-10-19
  • 录用日期:2015-12-11
  • 在线发布日期: 2017-05-18
  • 出版日期: