+高级检索
U-Nb合金中夹杂物的纳米压痕表征
作者:
作者单位:

中国工程物理研究院材料研究所

作者简介:

通讯作者:

中图分类号:

基金项目:

中国工程物理研究院重点项目(项目号TB120301)


Nanoindentation characterization of inclusions in U-Nb alloy
Author:
Affiliation:

Institute of Materials, China Academy of Engineering Physics

Fund Project:

Key Project of China Academy of Engineering Physics (Grant No. TB120301)

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用纳米压痕技术对铸态U-5.5Nb合金中Nb2C、U(C,N)以及基体力学性能进行了表征,根据获得的硬度值计算了屈服强度和塑性指数。实验结果表明Nb2C夹杂物的弹性模量和硬度最大,而U(C,N)夹杂物的弹性模量和硬度远小于Nb2C但明显高于基体;计算结果显示Nb2C夹杂物屈服强度最高而塑性指数值最小,倾向于发生弹性变形,U(C,N)夹杂物强度低但塑性指数值最大,更容易发生塑性变形并发生破裂。基体多步循环加载获得的弹性模量和硬度值与单次加载基本一致,并且弹性模量值和文献中报道的单向拉伸实验测得的值相符。

    Abstract:

    Mechanical properties of the Nb2C and U(N,C) inclusions and matrix in the U-5.5Nb alloy are characterized by nanoindentation and the yield strength and plasticity index are calculated from the obtained hardness. The result from experiment shows that the Nb2C inclusion has the highest elastic modulus and hardness, while the corresponding values of the U(N,C) inclusion are far less than those in the Nb2C inclusion but higher than matrix. Moreover, the result calculated from hardness shows that the yield strength of the Nb2C inclusion is the highest, but the plasticity index is the lowest, which reveals that the Nb2C inclusion inclines to elastic deformation. However, the yield strength of the U(N,C) inclusion is low and the plasticity index of the U(N,C) is the highest, which reveals that the U(N,C) inclusion prefers to plastic deformation and also can broke easily. Elastic modulus and hardness from multi-cycle load/unload test are close to those obtained by single load/unload test, in addition, the elastic modulus obtained from nanoindentation is accord to the value obtained by tensile test in the literature.

    参考文献
    相似文献
    引证文献
引用本文

陈冬. U-Nb合金中夹杂物的纳米压痕表征[J].稀有金属材料与工程,2019,48(1):165~170.[Chen Dong. Nanoindentation characterization of inclusions in U-Nb alloy[J]. Rare Metal Materials and Engineering,2019,48(1):165~170.]
DOI:10.12442/j. issn.1002-185X.20170414

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:2017-05-17
  • 最后修改日期:2017-08-25
  • 录用日期:2017-09-11
  • 在线发布日期: 2019-02-18
  • 出版日期: