+高级检索
热处理对激光选区熔化成形Inconel 718合金显微组织结构和力学性能的影响
作者:
作者单位:

1.华南理工大学 国家金属材料近净成形工程技术研究中心;2.广州昶联热等静压材料制造有限公司

基金项目:

国家自然科学基金重大仪器专项(51627805);广东省自然科学基金团队项目(2015A030312003);广东省科技攻关项目(2014B010129003)


Effect of Heat Treatment on microstructure and mechanical Properties of Inconel 718 alloy fabricated by selective laser melting
Author:
Affiliation:

1.National Engineering Research of Net-Sharp Forming for Metallic Material,South China University of Technology;2.Guangzhou Zoltrix HIP Material Co Ltd,Guangzhou

  • 摘要
  • | |
  • 访问统计
  • |
  • 参考文献 [25]
  • |
  • 相似文献
  • | | |
  • 文章评论
    摘要:

    本文主要研究了激光选区熔化成形Inconel 718合金经固溶时效(SA)、均匀化+固溶时效(H+SA)、热等静压+固溶时效(HIP+SA)三种热处理后显微组织结构的转变与力学性能之间的关系。实验结果表明,沉积态试样的晶粒内部存在大量树枝晶结构,枝晶间析出了大量硬脆Laves相。恰当的均匀化处理虽能促进δ相析出,但无γ "、γ "相,材料强度较低。热等静压(1080 ℃×1480 bar/2 h)能有效消除沉积态中的Laves相和微孔,经随后SA处理,材料的晶粒明显细化,晶界趋于平直,且强化相析出,材料的屈服强度、抗拉强度和硬度显著提高,分别达到1191 MPa、1361 MPa、490(HV0.2),断后伸长率达13.30 %,在提高材料强度的同时较大程度保留了材料的延展性,获得良好的综合力学性能。

    Abstract:

    This paper studies for the effect of solution-aging (SA), homogenization + solution aging (H+SA), Hot isostatic pressing + solution-aging (HIP + SA) three different heat treatments on the microstructure and mechanical properties of selective laser melting (SLM) formed Inconel 718 alloy. The as-built Inconel 718 has a large number of dendritic structures, and there are many brittle Laves phase precipitating among the interdendritic region. The δ phase was prone to precipitate when treated by proper homogenization, but the material can not be strengthened without γ"and γ " phases. Hot isostatic pressing(1080 ℃×1480 bar/2 h) can considerably removed Laves phase and micro pores of the as-fabricated samples, and combine with the solution aging treatment subsequently, it’s conductive to refine the grain size of the as-built samples, flat the grain boundaries, and promote the precipitation of γ "、γ " phase, so HIP+SA treatment significantly increases the strength of Inconel 718 alloy, the mechanical properties of Inconel 718 alloy reached their optimum combination at UTS=1361 MPa, 0.2% YS=1191 Mpa, and HV0.2 =490, and the elongation after breaking is 13.30%.

    参考文献
    [1] Decker R F. JOM[J], 2006,58(9):32-36
    [2] Guo Jianting(郭建亭). Superalloy Materials Science[M]. Beijing: Science Press,2008: 3-17
    [3] Wu Dan(武丹),Tian Lixi(田礼熙),Ma Chaoli(马朝利). Rare Metal Materials and Engineering [J],2015(44):1350
    [4] Zhang H Y,Zhang S H,Cheng M,et al. Materials Characterization [J],2010,61(1):49-53
    [5] Rao G A,Kumar M,Srinivas M,et al. Materials Science & Engineering A[J],2004,383(2):201-212
    [6] Qi H,Azer M, Ritter A. Metallurgical & Materials Transactions Part A[J],2009,40(10):2410-2422
    [7] Dun yong Deng. Licentiate Thesis [D]. Link?ping:Link?ping University,2018
    [8] Zhang D,Niu W,Cao X,et al. Materials Science and Engineering: A[J],2015,644:32-40
    [9] Wang Z,Guan K,Gao M,et al. Journal of Alloys and Compounds[J],2012,513(none):518-523
    [10] Cao G H, Sun T Y, Wang C H, et al. Materials Characterization [J],2018,136:398-406
    [11] Chlebus E, Gruber K, Ku?nicka B, et al. Materials Science and Engineering: A[J],2015,639:647-655
    [12] Trosch T , Johannes Str??ner, Rainer V?lkl, et al. Materials Letters[J], 2016, 164:428-431
    [13] Liu W, Dupont J N. Acta Materialia[J], 2004,52(16):4833-4847
    [14] Mclouth T D, Bean G E, Witkin D B,et al. Materials & Design[J],2018,149:205-213
    [15] V.A. Popovich, E.V. Borisov, A.A. Popovich, et al. Materials & Design[J],2017,114:441-449
    [16] Xing Li, Shi J J, Wang C H, et al. Journal of Alloys and Compounds[J],2018, 64:639-649
    [17] Deng D, Peng R L, Brodin H,et al. Materials Science and Engineering: A[J],2018,713:294-306
    [18] S. A. David, J. M. Vitek, L. A. Boatner & M. Rappaz. Materials Science and Technology[J], 1995,11(9):939-948
    [19] Choi J P, Shin G H, Yang S, et al. Powder Technology[J], 2017,310:60-66
    [20] Antonsson T, Fredriksson H. Metallurgical and Materials Transactions A (Physical Metallurgy and Materials Science)[J], 2005,36(1):85-96
    [21] Sames W. Thesis for Doctorate[D].Texas:Texas A&M University,2015
    [22] Long Y T,Nie P L,Li Z G,et al. Transactions of Nonferrous Metals Society of China[J],2016,26(2):431-436
    [23] Wen D X, Lin Y C,Chen J,et al. Materials Science and Engineering: A[J],2015,620:319-332
    [24] Yongchang L,Qianying G,Chong L I,et al. Acta Metallurgica Sinica[J], 2016
    [25] J Li,Z Zhao,P Bai,et al. Journal of Alloys and Compounds [J],2019,772:861-870
    相似文献
    引证文献
    网友评论
    网友评论
    分享到微博
    发 布
引用本文

张荣,柳中强,黄嘉豪,朱权利,肖志瑜.热处理对激光选区熔化成形Inconel 718合金显微组织结构和力学性能的影响[J].稀有金属材料与工程,2021,50(1):255~262.[Zhang Rong, Liu Zhongqiang, Huang Jiahao, Zhu Quanli, Xiao Zhiyu. Effect of Heat Treatment on microstructure and mechanical Properties of Inconel 718 alloy fabricated by selective laser melting[J]. Rare Metal Materials and Engineering,2021,50(1):255~262.]
DOI:10.12442/j. issn.1002-185X.20200009

复制
文章指标
  • 点击次数:917
  • 下载次数: 1362
  • HTML阅读次数: 178
  • 引用次数: 0
历史
  • 收稿日期:2020-01-06
  • 最后修改日期:2020-02-17
  • 录用日期:2020-02-21
  • 在线发布日期: 2021-02-05