+高级检索
铸造工艺对钛合金Ti5Al2.5Sn ELI铸态组织及性能的影响
作者:
作者单位:

沈阳铸造研究所有限公司 高端装备轻合金铸造技术国家重点实验室

作者简介:

通讯作者:

中图分类号:

基金项目:

辽宁省科学技术计划(项目号2019JH1/10100004)


Influence of Casting Process on the Structure and Mechanical Properties of as-cast Ti5Al2.5Sn ELI Titanium Alloy
Author:
Affiliation:

State Key Laboratory of Light Alloy Casting Technology for High-end Equipment,Shenyang Research Institute of Foundry Co.,Ltd.

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    Ti5Al2.5Sn ELI钛合金是航空航天等领域重要的结构材料。本文采用三种铸型同炉浇注的方法研究了铸造工艺对该合金铸态组织和室温拉伸性能的影响。结果表明,该合金石墨型铸造试样表面粗糙,陶瓷型和金属型的则较光滑;石墨型试样宏观组织为大量等轴晶和少量柱状晶,金属型的为少量等轴晶和大量柱状晶,陶瓷型的为粗大柱状晶和等轴晶;不同工艺下显微组织均由不规则边界α集束组成,其内部为片状α相,石墨型的α片宽度最小,金属型的次之,陶瓷型的最大;该合金铸态抗拉强度715~731 MPa、伸长率8~15 %,石墨型的伸长率最高,金属型的次之,陶瓷型的最低,铸造工艺对该合金塑性影响强烈,但对强度的影响较小;铸型表面形貌、导热系数、α集束大小及α片厚度的不同是上述现象产生的主要原因。

    Abstract:

    Titanium alloy Ti5Al2.5Sn ELI is an important structural material in the field of aerospace and others. In the paper, the influence of casting process on the as-cast structure and tensile properties of titanium alloy Ti5Al2.5Sn ELI at room temperature was studied by pouring three kinds of mold with one furnace alloy. The results show that the surface of casting samples from graphite mold is rough, while that of the ceramic and metal mold is smooth; the macrostructure of samples from graphite mold is composed of numbers of equiaxed crystal and some columnar crystal, that of the metal mold is some equiaxed crystal and numbers of columnar crystal, and that of the ceramic mold is numbers of columnar crystal and little equiaxed crystal; the microstructure of the alloy under different processes is composed of irregular boundary α cluster, and the inner part is sheet α phase, and the width of α sheet of graphite mold is the smallest, that of metal mold is the second, and that of ceramic mold is the largest; the tensile strength of alloy is 715~731 MPa, the elongation is 8~15 %, the elongation of samples from the graphite mold is the highest, that of metal mold is the second, that of ceramic mold is the lowest, and the influence of molds on the elongation is obvious, but that on the strenths is little; the difference of surface morphology and thermal conductivity of mold, and the difference of α cluster size and α sheet thickness of samples are the main reasons for the phenomena.

    参考文献
    相似文献
    引证文献
引用本文

刘时兵,娄延春,赵军,李重阳,刘鸿羽,张爱博.铸造工艺对钛合金Ti5Al2.5Sn ELI铸态组织及性能的影响[J].稀有金属材料与工程,2021,50(2):575~580.[Liu Shibing, Lou Yanchun, Zhao Jun, Li Chongyang, Liu Hongyu, Zhang Aibo. Influence of Casting Process on the Structure and Mechanical Properties of as-cast Ti5Al2.5Sn ELI Titanium Alloy[J]. Rare Metal Materials and Engineering,2021,50(2):575~580.]
DOI:10.12442/j. issn.1002-185X.20200170

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:2020-03-16
  • 最后修改日期:2020-06-04
  • 录用日期:2020-06-04
  • 在线发布日期: 2021-03-09
  • 出版日期: