+高级检索
Y2O3含量对激光熔覆0.3C-18Cr合金涂层组织和性能的影响
DOI:
作者:
作者单位:

1.兰州理工大学;2.广东省阳江市五金刀剪产业技术研究院

作者简介:

通讯作者:

中图分类号:

TG142.1+4

基金项目:

国家自然资助(51461029);广东省“扬帆计划”引进创新创业团队专项资助(2015YT02G090);广东省2017年科技发展专项资金(协同创新与环境平台建设)资助(611229498090);阳江市五金刀剪与镍合金产业增材制造技术创新平台建设项目资助(2015B020221002)


Influence of Y2O3 Content on Microstructure and Properties of Laser Cladding 0.3C-18Cr Alloy Coating
Author:
Affiliation:

1.Lanzhou University of Technology;2.Lan Zhou University of Technology;3.Hardware Knife Cut Industrial Technology Research Institute Yangjiang, Yangjiang

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    在3Cr14不锈钢基体上激光熔覆制备不同Y2O3含量的0.3C-18Cr复合涂层。采用金相显微镜(OM)、扫描电子显微镜(SEM)、X射线衍射(XRD)、显微硬度仪等设备研究了不同Y2O3含量对熔覆层的微观结构、相组成及硬度的影响。结果表明,未添加Y2O3试样熔覆层有较多孔洞,熔覆层组织由晶内铁素体、晶界分布的上贝氏体及少量马氏体组成;加入在3Cr14不锈钢基体上激光熔覆制备不同Y2O3含量的0.3C-18Cr复合涂层。采用金相显微镜(OM)、扫描电子显微镜(SEM)、X射线衍射(XRD)、显微硬度仪等设备研究了不同Y2O3含量对熔覆层的微观结构、相组成及硬度的影响。结果表明,未添加Y2O3试样熔覆层有较多孔洞,熔覆层组织由晶内铁素体、晶界分布的上贝氏体及少量马氏体组成;加入Y2O3后熔覆层枝晶长度减小且数量减少,枝晶尖端钝化且径向粗化,长径比减小,同时熔覆层气孔减少,熔覆层得到净化;熔覆层组织由板条马氏体+晶界少量贝氏体构成;且随Y2O3含量增加,板条马氏体略有粗化,贝氏体数量明显减少,贝氏体碳化物的碳浓度增大,碳化物类型由低碳型碳化物向高碳型碳化物转变。加入Y2O3后,熔覆层显微硬度显著提高,添加2% Y2O3时熔覆层的硬化效果最佳,比未添加Y2O3时增加160 HV0.2。

    Abstract:

    PreparationSofS0.3C18CrScompositeScoatingsSwithSdifferentSY2O3 contentsSonS3Cr14 stainlessSsteelSsubstrateSbySlaserScladdig. The effects of different Y2O3 contents on the microstructure, phase composition and hardness of the cladding layer were studied by metallographic microscope (OM), scanning electron microscope (SEM), X-ray diffraction (XRD) and microhardness tester. The results show that there are many porous holes in the cladding layer without adding Y2O3, and the microstructure of the cladding layer consists of intragranular ferrite, bainite with grain boundary distributed and a small amount of martensite; After adding Y2O3, the dendrite length of the cladding layer is reduced and the number decreases, the dendrite tip is passivated and radially coarsening, the length to diameter ratio decreases, meanwhile the pores of the cladding layer decrease, and the cladding layer is purified. The microstructure of the cladding layer is composed of lath martensite and a small amount of bainite in the grain boundary. With the increase of Y2O3, the lath martensite is slightly coarsened, the number of bainite decreases obviously, the carbon concentration of bainite carbide increases, and the type of lamellar carbides transforms from low carbon carbide to high carbon carbide. After adding Y2O3, the microhardness of the clad layer is significantly improved,; When added 2% Y2O3, the hardening effect of the cladding layer comes up to the best, which was 160 HV0.2 higher than that without adding Y2O3.

    参考文献
    相似文献
    引证文献
引用本文

郭铁明,蒲亚博,张瑞华,栗子林,李强. Y2O3含量对激光熔覆0.3C-18Cr合金涂层组织和性能的影响[J].稀有金属材料与工程,2019,48(11):3643~3650.[guotieming, puyabo, zhangruihua, lizilin, liqinag. Influence of Y2O3 Content on Microstructure and Properties of Laser Cladding 0.3C-18Cr Alloy Coating[J]. Rare Metal Materials and Engineering,2019,48(11):3643~3650.]
DOI:[doi]

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:2018-04-24
  • 最后修改日期:2018-06-07
  • 录用日期:2018-07-30
  • 在线发布日期: 2019-12-10
  • 出版日期: