+高级检索
电弧增材制造(WAAM)ZL114A铝合金组织与性能的研究
DOI:
作者:
作者单位:

1.东北大学;2.中国兵器科学研究院宁波分院;3.抚顺东工冶金材料技术有限公司

作者简介:

通讯作者:

中图分类号:

基金项目:


Investigation on microstructure and properties of aluminum alloy (ZL114A) by wire arc additive manufacturing (WAAM)
Author:
Affiliation:

1.Northeastern University;2.North East Industrial Materials Metallurgy Co,Ltd

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用金相显微镜、扫描电镜、电子万能试验机等分析测试手段,研究了电弧增材制造工艺方法对ZL114A铝合金组织与性能的影响。与传统铸造成形方法相比,铸态组织具有更小的枝晶间距、Si相细小分布均匀;化学成分可有效控制;T6热处理后,Si相球化充分,第二相弥散分布在α-Al基体上,力学性能显著提升,抗拉强度、屈服强度及延伸率分为360MPa、315MPa、7.5%,延伸率是砂型铸造试样的2.1倍,拉伸断口呈现韧性断裂特征。WAAM成形试样缺陷主要为小于30μm的气孔,经过热处理后气孔数量减少,尺寸有变大趋势。

    Abstract:

    The effect of wire arc additive manufacturing process on the structure and properties of aluminum alloy (ZL114A) was studied by means of metallographic microscope, scanning electron microscope and electronic universal test. Compared with the traditional casting method, the structure of as-deposited WAAM ZL114A has smaller dendrite spacing, the distribution of fine Si-phase is uniform, and the chemical composition is controlled effectively. Through T6 heat treatment process, Si-phase is fully spheroidized and the second phase is dispersed on the matrix of alpha-Al. Meanwhile, the mechanical properties are significantly improved. The tensile strength, yield strength and elongation are 360MPa, 315 MPa and 7.5%, respectively. Especially, the elongation is 2.1 times than that of sand casting sample, and the tensile fracture is characterized by ductile fracture. The defects of ZL114A(WAAM) are mainly pores less than 30 μm. After heat treatment, the number of pores decreases and the size increases.

    参考文献
    相似文献
    引证文献
引用本文

李承德,顾惠敏,王伟,翟玉春,明珠,王帅,任玲玲,王振飚.电弧增材制造(WAAM)ZL114A铝合金组织与性能的研究[J].稀有金属材料与工程,2019,48(9):2917~2922.[Li Chengde, Gu Huimin, Wang Wei, Zhai Yuchun, Ming Zhu, Wang Shuai, Ren Lingling, Wang Zhenbiao. Investigation on microstructure and properties of aluminum alloy (ZL114A) by wire arc additive manufacturing (WAAM)[J]. Rare Metal Materials and Engineering,2019,48(9):2917~2922.]
DOI:[doi]

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:2018-11-15
  • 最后修改日期:2019-01-17
  • 录用日期:2019-02-21
  • 在线发布日期: 2019-10-09
  • 出版日期: