+高级检索
纳米氧化铜对磷酸盐胶黏剂耐水性能的影响
DOI:
作者:
作者单位:

天津大学材料科学与工程学院

作者简介:

通讯作者:

中图分类号:

基金项目:

智库基金-特种密封材料及其系列化研究(项目号201707051001)


Effect of nano CuO on water resistance of phosphate adhesive
Author:
Affiliation:

Materials Science and Engineering of Tianjin University

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以H3PO4和Al(OH)3为基体,纳米氧化铜为填料来制备磷酸盐无机胶黏剂。胶黏剂粘结的莫来石片,在人工海水浸泡168小时后,测试其剪切强度,并以此强度为标准,来探究纳米氧化铜的加入对磷酸盐胶黏剂耐水性能的影响。研究结果表明当纳米氧化铜加入量为基体的20wt%时,莫来石粘结片浸泡在人工海水168小时的最佳剪切强度为7.13MPa。最佳配方粘结的莫来石片经150oC至1300oC处理后,浸泡在人工海水的最低剪切强度为2.31MPa,通过XRD、SEM等方法分析纳米氧化铜的加入对磷酸盐胶黏剂耐水性能的影响。

    Abstract:

    : Phosphate adhesive were prepared with the H3PO4 and Al (OH)3 as the matrix and nano CuO as the inorganic fillers. The influence of nano CuO on the water resistance of phosphate adhesives was investigated by soaking mullite joints that were bonded by the adhesive in artificial seawater for 168h. The results show that the nano CuO could improve the water resistance of the adhesive. The shear strength of mullite joint was 7.13MPa which is the best strength after immersed in artificial water whenthe content ofnano CuO was 20wt% in matrix. It has good water resistance within the whole heat-treatment temperature range from 150oC to 1300oC. The lowest shear strength is 2.31MPa after heat-treatment at 1300oC and immersed in artificial seawater. The effects of nano CuO on the water resistance of phosphate adhesive were analyzed by XRD and SEM.

    参考文献
    相似文献
    引证文献
引用本文

刘子浩,王明超,郭安然,刘家臣.纳米氧化铜对磷酸盐胶黏剂耐水性能的影响[J].稀有金属材料与工程,2020,49(2):577~581.[Zihao Liu, Mingchao Liu, Anran Guo, Jiachen Liu. Effect of nano CuO on water resistance of phosphate adhesive[J]. Rare Metal Materials and Engineering,2020,49(2):577~581.]
DOI:[doi]

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:2019-03-18
  • 最后修改日期:2019-04-24
  • 录用日期:2019-10-14
  • 在线发布日期: 2020-03-12
  • 出版日期: