+高级检索
感应电流频率对原位合成Al3Ti/Al复合材料组织及性能的影响[1]
DOI:
作者:
作者单位:

西安科技大学材料科学与工程学院

作者简介:

通讯作者:

中图分类号:

基金项目:

科技部国际合作项目(2015DFR50990-01);陕西省纳米材料重点实验室开放课题(18JS060)和(18JS075);


Effect of Induced Current Frequency on Microstructure and Properties of In-situ Synthesized Al3Ti/ Composites
Author:
Affiliation:

College of Materials Science and Engineering, Xi´an University of Science and Technology

Fund Project:

International cooperation project of Ministry of science and technology China (2015DFR50990-01); Open topic of Shaanxi Key Laboratory of Nano-materials and Technology, Xi"an University of Architecture and Technology(18JS060) and (18JS075).

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以金属铝为基体,以钛纤维为反应源获得铸态的钛铝预制复合体,通过对其施加不同频率的交变电流,在外场作用下促进铝、钛原子间的反应,以期获得Al3Ti颗粒增强铝基复合材料。通过差热分析(DTA)预判断钛铝间反应温度为800℃左右,通过XRD、SEM和磨损测试对所得复合材料进行分析表征。结果表明:原位反应最佳参数为:频率7KHz、电流8A、反应时间5min。此参数下,钛纤维完全反应,主要相Al3Ti分散性较好,颗粒尺寸细化至3μm左右;在10N载荷条件下,随着频率的增大,摩擦系数先降后升,频率7KHz时的摩擦系数为最低值0.2,磨损量较最少,耐磨性能较优。

    Abstract:

    Using metal Al as substrate and titanium fiber as reactive source,an Al3Ti/Al composite was fabricated by applying induction heating,and the inductive magnetic field generate by the coil was used to promote the in-situ reaction rate of aluminum and titanium.The reaction temperature was preliminarily judged by differential thermal analysis (DTC) to be about 800 degrees, and the obtained samples were characterized by X-ray diffraction(XRD),scanning electron microscopy(SEM) and wear testers.The results show that when the alternating current frequency is 7KHz, the current is 8A, and the time is 5min.,the titanium fiber react with Al completely,and the dispersed distribution of Al3Ti particles are in-situ synthesized, and the average size of the particles reach 3μm; Under the condition of 10N load and air as medium, the friction coefficient decreases first and then increases with the increase of alternating current frequency. The friction coefficient at the frequency of 7KHz is the lowest value of 0.2, the wear amount is the least, and the wear resistance is optimal.

    参考文献
    相似文献
    引证文献
引用本文

闫俞廷,牛立斌,安玉姣,王圣雅,党利娟,闫梦婷,付哲.感应电流频率对原位合成Al3Ti/Al复合材料组织及性能的影响[1][J].稀有金属材料与工程,2020,49(6):2175~2181.[yanyuting, Niu Libin, An Yujiao, Wang Shengya, Dang Lijuan, Yan Mengting, Fu Zhe. Effect of Induced Current Frequency on Microstructure and Properties of In-situ Synthesized Al3Ti/ Composites[J]. Rare Metal Materials and Engineering,2020,49(6):2175~2181.]
DOI:[doi]

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:2019-08-14
  • 最后修改日期:2020-01-13
  • 录用日期:2020-02-20
  • 在线发布日期: 2020-07-09
  • 出版日期: